Plastic Injection Molding
CorePULL庐 Hydraulic Power Systems
Many plastic injection machine manufacturers do not want to pair a hot, loud, large, and inefficient hydraulic system next to a clean and efficient machine. CorePULL plastic injection molding hybrid hydraulic systems have an inverter controlled variable speed electric motor that solves these issues.
Once the system's desired pressure is met, the CorePULL unit slows to approximately 300 RPM while holding pressure. When there is a need for pressure, the CorePULL responds by accelerating to 4,000 RPM within 1/10 of a second; accomplished by utilizing a pressure transducer to sense demands. This technology reduces heat generation allowing for cooler operating temperatures.
Multiple cores or auxiliary functions, such as valve gates can be run using a manifold with a variety of circuit configurations. For better functionality, the keypad on the front of the CorePULL units allows for a fast and easy way to change pressure and flow.
CorePULL Benefits:
- Save up to 63% on energy costs
- No cooling water required
- Quiet operation 60 to 68 dba noise level
- Operates just above room temperature
- Inverter technology
The Corepull is the perfect hydraulic pairing to all-electric injection molding machines that want to match the efficiency of their machine to the power of a hydraulic system.
Common or custom, contact 吉林“岳欣悦”00后少女10P事件 to inquire about a CorePULL solution for your plastic injection molding machine, click here for more details, or call Kyle Crull at 815-704-7858.
- Unlimited Valves (D03 size)
- 3 Gallon Reservoir
- Single Pump System
- 12" W x 20" L x 25" H
- Unlimited Valves (D05 size)
- 10 Gallon Reservoir
- Double Pump System
- 20" W x 28" L x 42" H
- Unlimited Valves (D05 size)
- 15 Gallon Reservoir
- Double Pump System
- 25" W x 28" L x 42" H
- Unlimited Valves (D05 or D08 size)
- 15 Gallon Reservoir
- Double Pump System
- 25" W x 36" L x 46" H
- Unlimited Valves
- 50 Gallon Reservoir
- Double Pump System
- 36" Deep x 60" Wide
- 10-15 Gallon Reservoir
- Double Pump System
- 33" W x 40" L x 18" H
Options
Econo J-Box
- Enclosure with screw cover-mounted (on left-hand end of SUT) and wired.
- Terminal strip for 2 valves (8 wires) and 4 control signals to SUT (parameter switching & E stop).
- Wiring from J-Box to 2 valves.
- Wiring of 15' x 12 gage power cord with flying leads to SUT controller (does not go through J-Box).
- Wiring of (4) control signals from J-box to SUT controller.
- Wiring of 15' x 18-12 conductor control cable with flying leads to the J-Box.
All of the above would be mounted and wired. The customer will need to connect the control cable and power cord to the machine side.
Remote Mounted Keypad
- Great for units mounted under the press.
- Weather-tight enclosure.
- Pre-wired with 25 ft. of cable.
- Replaces the function of the keypad on the SUT.
- Can be mounted horizontal or vertical.
Super-Shot Accumulator
This factory option is designed for lightning-fast response times for those tough applications where every 1/10th of a second counts. A small piston accumulator is charged during dwell time and gives an immediate burst of fluid power whenever the solenoid valve is energized. A Dual Port Flow Control Module is included to tune the extend and retract speeds.
Larger accumulator systems for Rack Units are available upon request.
Super-Shot options Include:
- Piston accumulator 800 PSI precharge
- Mounting plates
- Isolation mounting clamps
- Dual Port Flow Control Module
